Owl ! It's raining all week !

 

Here, my feedback of my tests on an extension (removable and aesthetic) for all Mini modeles 's fenders

 

ūüėė


 

 

 

 

 

 

 

FOLLOW-ME MODE DOES NOT WORK ANYMORE ...

unplugged the connector...
unplugged the connector...

My "Follow-me" mode was no longer responding after a shock, just now.

I turned off the Mini, I removed the cover, and I unplugged the connector

I turned on the Mini

Then I turned it off again

I reconnected the connector

 

Turned on, now "Follow-me" mode works fine


Removing Mini PLUS Pads

Merci/Thanks/ŤįĘŤįĘ @ahzgh

 

1 / Prepare 1 hex key, remove the 12 screws of the underbody

2 / Open the underbody, disconnect the connector

3 / Each orange circle tells you which parts to disassemble: Remove the 6 screws on the wing

4 / Lift the mudguard vertically and remove it

5 / Install the Pad

6 / Reproduce the assembly in reverse

 

When you clean your MINI, you can not remove and simply put back the pads.

Pads that are replaced from above are not properly replaced.

The plate, under the pads, which touches the joystick loses adhesion.

The result in driving can be disastrous. 

The Mini no longer respond properly, no longer has the same responsiveness, driving is derived.

The Mini is the miniaturization of a PT-type Segway

All parts are nested to each other

If you remove the pads, you must replace them beginning with dismantling the bases of the pads.

There are several notches provided for inserting the pads.

 

Below, a great tutorial video from Speedyfeet how to remove and replace pads like for the Mini PRO


Removing Hubcaps

The technique of the video did not work for me, so I bought this suction cup windshield, very effective.



CLEAN HIS MINI PLUS (FENDERS & hubcaps)

Use very fine sandpaper on the stripes without exceeding the area of the stripes

 

ťĚ쌳łśĄüŤįʬ†http://bbs.xiaomi.cn/t-12316772¬†&¬†http://bbs.xiaomi.cn/t-12347921¬†MERCI A L'UTILISATEUR

 

an old scrub sponge and a foaming spray with bleach
an old scrub sponge and a foaming spray with bleach

Use spray bleach (bleach spray that foam), let it act for a few minutes,

 

Use old scrub scouring sponge and you rub hard on the whole surface

only if the scouring sponge is very worn so as not to scratch the mudguards.

Rinsing with a lot of water, the Mini Plus has to be tilted backwards, for the water to flow, pay attention to the lighthouse in the steering column, the water can infiltrate paste a sticker over, dry well with a cloth and tilting the Mini back

 


remove the shell under the Mini to clean it

If you have no problem for the warranty, you can remove the shell under the Mini, I did it.

I used a dry air spray, I cleaned the dust and mud, with a wipe I cleaned the seal

I repositioned the seal in the shell, because he was glued to the frame

I inspected the screws and the condition of the chassis

I reassembled the shell, and screwed several times so that the seal is positioned according to the chassis

we see the difference between the area protected by the joint and the very dirty exterior area
we see the difference between the area protected by the joint and the very dirty exterior area
a lot of dust and dried mud
a lot of dust and dried mud
the seal remained glued to the frame we clean the seal with a wipe
the seal remained glued to the frame we clean the seal with a wipe
we check the screws and the general condition
we check the screws and the general condition
here it is correctly repositioned in the hull
here it is correctly repositioned in the hull